AMIC Technology
Showing all 6 results
AMIC Technology - A25L080M-F
XProduct SKU: A25L080M-F
AMIC Technology inventory available from stock
From£0.25 (Ex. VAT)
2148 In stock
Make an Enquiry
AMIC Technology - A25Lxxx Series Serial Flash
XProduct SKU: A25L010AO-F-P
The A25L020/A25L010/A25L512 are 2M/1M/512K bit Serial Flash Memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus. The memory can be programmed 1 to 256 bytes at a time, using the Page Program instruction. The memory is organized as 4/2/1(A25L020/A25L010/A25L512) blocks, each containing 16 sectors. Each sector is composed of 16 pages. Each page is 256 bytes wide. Thus, the whole memory can be viewed as consisting of 1024/512/256 (A25L020/A25L010/A25L512) pages, or 262,144/131,072/ 65,536 (A25L020/A25L010/A25L512) bytes. The whole memory can be erased using the Chip Erase instruction, a block at a time, using Block Erase instruction, or a sector at a time, using the Sector Erase instruction.
CONTACT US FOR VOLUME PRICING
Enquire for availability
Make an Enquiry
AMIC Technology - A290xx Series NOR Flash
XProduct SKU: A29010A-55F-P
The A29001A is a 5.0 volt-only Flash memory organized as 131,072 bytes of 8 bits each. The A29001A offers the RESET function, but it is not available on A290011A. The 128 Kbytes of data are further divided into seven sectors for flexible sector erase capability. The 8 bits of data appear on I/O0 - I/O7 while the addresses are input on A0 to A16. The A29001A is offered in 32-pin PLCC, PDIP and TSOP packages. This device is designed to be programmed insystem with the standard system 5.0 volt VCC supply. Additional 12.0 volt VPP is not required for in-system write or erase operations. However, the A29001A can also be programmed in standard EPROM programmers.
CONTACT US FOR VOLUME PRICING
Enquire for availability
Make an Enquiry
AMIC Technology - A29L0xx Series Low Power NOR Flash
XProduct SKU: A29L040AL-70F-P
The A29L040A is a 3.0 volt-only Flash memory organized as 524,288 bytes of 8 bits each. The 512 Kbytes of data are further divided into eight sectors of 64 Kbytes each for flexible sector erase capability. The 8 bits of data appear on I/O0 - I/O7 while the addresses are input on A0 to A18. The A29L040A is offered in 32-pin DIP, PLCC, TSOP (8mm x 20mm) packages. This device is designed to be programmed in-system with the standard system 3.0 volt VCC supply. Additional 12.0 volt VPP is not required for in-system write or erase operations. However, the A29L040A can also be programmed in standard EPROM programmers.
CONTACT US FOR VOLUME PRICING
Enquire for availability
Make an Enquiry
AMIC Technology - A43Lxxx Series SDRAM
XProduct SKU: A43L0616BV-6F-P
The A43L0616B is 16,777,216 bits synchronous high data rate Dynamic RAM organized as 2 X 524,288 words by 16 bits, fabricated with AMIC’s high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock. I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable latencies allows the same device to be useful for a variety of high bandwidth, high performance memory system applications.
CONTACT US FOR VOLUME PRICING
Enquire for availability
Make an Enquiry
AMIC Technology - A62xxxx Series Low Power SRAM
XProduct SKU: A623308A-70SF-P
The A623308A is a low operating current 65,536-bit static random access memory organized as 8,192 words by 8 bits and operates on a voltage from 4.5V to 5.5V. Inputs and three-state outputs are TTL compatible and allow for direct interfacing with common system bus structures. Minimum standby power is drawn by this device when CE is at a high level, independent of the other input levels. Data retention is guaranteed at a power supply voltage as low as 2.0V.
CONTACT US FOR VOLUME PRICING
Enquire for availability
Make an Enquiry