Microcontrollers
Showing all 9 results
Holtek HT12A / HT12E 2(12) Series of Encoders
From£0.60(Ex. VAT)
Holtek HT12A / HT12E 2(12) Series of Encoders
XProduct SKU: HT12E-18DIPLF-P
Holtek HT12A / HT12E 2(12) Series of Encoders
General Description The 2(12) encoders are a series of CMOS LSIs for remote control system applications. They are capable of encoding information which consists of N address bits and 12N data bits. Each address/data input can be set to one of the two logic states. The programmed addresses/data are transmitted together with the header bits via an RF or an infrared transmission medium upon receipt of a trigger signal. The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 212 series of encoders. The HT12A additionally provides a 38kHz carrier for infrared systems. Applications - Burglar alarm system - Smoke and fire alarm system - Garage door controllers - Car door controllers - Car alarm system - Security system - Cordless telephones - Other remote control systemsFeatures
- Operating voltage - 2.4V~5V for the HT12A - 2.4V~12V for the HT12E - Low power and high noise immunity CMOS technology - Low standby current: 0.1 A (typ.) at VDD=5V - HT12A with a 38kHz carrier for infrared transmission medium - Minimum transmission word - Four words for the HT12E - One word for the HT12A - Built-in oscillator needs only 5% resistor - Data code has positive polarity - Minimal external components - Pair with Holtek's 2(12 )series of decoders - 18-pin DIP, 20-pin SOP packageFrom£0.60(Ex. VAT)
Enquire for availability
Make an Enquiry
Holtek HT12D / HT12F 2(12) Series of Decoders
From£0.60(Ex. VAT)
Holtek HT12D / HT12F 2(12) Series of Decoders
XProduct SKU: HT12D-18DLF-P
General Description
The 2(12) decoders are a series of CMOS LSIs for remote control system applications. They are paired with Holtek s 212 series of encoders (refer to the encoder/decoder cross reference table). For proper operation, a pair of encoder/decoder with the same number of addresses and data format should be chosen.
The decoders receive serial addresses and data from a programmed 212 series of encoders that are transmitted by a carrier using an RF or an IR transmission medium. They compare the serial input data three times continuously with their local addresses. If no error or unmatched codes are found, the input data codes are decoded and then transferred to the output pins. The VT pin also goes high to indicate a valid transmission.
The 2(12) series of decoders are capable of decoding informations that consist of N bits of address and 12 N bits of data. Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and HT12F is used to decode 12 bits of address information.
Applications
Burglar alarm system
Smoke and fire alarm system
Garage door controllers
Car door controllers
Car alarm system
Security system
Cordless telephones
Other remote control systems
Features
Operating voltage: 2.4V~12V Low power and high noise immunity CMOS technology Low standby current Capable of decoding 12 bits of information Binary address setting Received codes are checked 3 times Address/Data number combination HT12D: 8 address bits and 4 data bits HT12F: 12 address bits only Built-in oscillator needs only 5% resistor Valid transmission indicator Easy interface with an RF or an infrared transmission medium Minimal external components Pair with Holtek s 212 series of encoders 18-pin DIP, 20-pin SOP packageFrom£0.60(Ex. VAT)
32 In stock
Make an Enquiry
Holtek HT1380/HT1381 Serial Timekeeper Chip
From£0.65(Ex. VAT)
Holtek HT1380/HT1381 Serial Timekeeper Chip
XProduct SKU: HT1381-8SOPLF
Holtek HT1380/HT1381 Serial Timekeeper Chip
General Description The HT1380/HT1381 is a serial timekeeper IC which provides seconds, minutes, hours, day, date, month and year information. The number of days in each month and leap years are automatically adjusted. The HT1380/HT1381 is designed for low power consumption and can operate in two modes: one is the 12-hour mode with an AM/PM indicator, the other is the 24-hour mode. The HT1380/HT1381 has several registers to store the corresponding information with 8-bit data format. A 32768Hz crystal is required to provide the correct timing. In order to minimize the pin number, the HT1380/HT1381 use a serial I/O transmission method to interface with a microprocessor. Only three wires are required: (1) REST, (2) SCLK and (3) I/O. Data can be delivered 1 byte at a time or in a burst of up to 8 bytes Applications Microcomputer serial clock Clock and CalendarFeatures
Operating voltage: 2.0V~5.5V Maximum input serial clock: 500kHz at VDD=2V, 2MHz at VDD=5V Operating current: less than 1A at 2V, less than 1.2A at 5V TTL compatible - VIH: 2.0V~VDD+0.3V at VDD=5V - VIL: 0.3V~+0.8V at VDD=5V Two data transmission modes: single-byte, or burst mode Serial I/O transmission All registers store BCD format HT1380: 8-pin DIP package HT1381: 8-pin SOP packageFrom£0.65(Ex. VAT)
Enquire for availability
Make an Enquiry
Holtek HT1650 6432 LCD Controller for I/O MCU
From£2.15(Ex. VAT)
Holtek HT1650 6432 LCD Controller for I/O MCU
XProduct SKU: HT1650-128QFPLF
Holtek HT1650 6432 LCD Controller for I/O MCU
HT1650 is a peripheral device specially designed for I/O type MCUs which are used to expand the display capability. The max. display segment of the device are 2048 patterns (64 segments and 32 commons). It also supports four data bits interface, buzzer sound, Watchdog Timer or time base timer functions. The HT1650 is a memory mapping and multi-function LCD controller. It can control TN-type (Twisted Nematic) or STN-type (Super Twisted Nematic) LCDs. The software configuration feature of the HT1650 make it suitable for multiple LCD applications including LCD modules and display subsystems. Only six lines (CS, WR, DB0~DB3) are required for the interface between the host controller and the HT1650 Application Leisure products Games Personal digital assistant Cellular phone Global positioning system Consumer electronicsFeatures
- Operating voltage: 2.7V~5.2V - Built-in 32kHz RC oscillator - External 32.768kHz crystal oscillator or 32kHz frequency source input - Standby current: <1A at 3V, <2A at 5V - Internal resistor type: 1/6 bias or 1/5 bias, 1/32 duty, and 1/16 duty - Three selectable LCD frame frequencies: 64Hz, 89Hz or 170Hz - Max. of 64 32 patterns, 64 segments and 32 commons - 80 segments and 16 commons selectable by command method - Built-in bit-map display RAM: 2048 bits (=64 32 bits) - Built-in internal resistor type bias generator - Six-wire interface (four data wires) - Eight kinds of time base or WDT selection - Time base or WDT overflow output - R/W address auto increment - Built-in buzzer driver (2kHz/4kHz) - Power down command reduces power consumption - Software configuration feature - Data mode and Command mode instructions - Three data accessing modes - Provides VLCD pin to adjust LCD operating voltage and max. VLCD voltage up to 7V - Provides three kinds of bias current programming - Control of TN-type and STN-type LCDs - 128-pin QFP packageFrom£2.15(Ex. VAT)
Enquire for availability
Make an Enquiry
Microchip – BM83 eval
From£365.00(Ex. VAT)
4 In stock
Make an Enquiry
Microchip PIC18-Q43 Family
Enquire for availability
Make an Enquiry
Microchip PIC24F16
From£2.15(Ex. VAT)
135 In stock
Make an Enquiry
Microchip PIC24F16KA
From£2.20(Ex. VAT)
Enquire for availability
Make an Enquiry
Silicon Labs – EFM 8 Microcontroller
From£1.85(Ex. VAT)
Enquire for availability
Make an Enquiry